SparePartsMatcher

Truma heater

Truma VarioHeat - CP plus VarioHeat panel fault codes (EU edition)

All 10 codes, what each one means and what to check, from Truma VarioHeat (eco / comfort) - operating instructions with CP plus VarioHeat and CP classic VarioHeat (39050-00070, rev 00, 07/2016).

#2GASNo flame detected at the burner.

Likely cause: Gas closed or empty, iced regulator, too much butane, or blocked air intake/exhaust.

Gas fault: get a licensed gas fitter

Turn the gas off at the bottle and run the appliance on another power source until it's checked. Only a licensed gas fitter should work on the gas side.

Truma's checks, in order: Open valves, change cylinder, use EisEx and propane, clear the cowl of ice or debris.

Source: Truma VarioHeat (eco / comfort) - operating instructions with CP plus VarioHeat and CP classic VarioHeat (39050-00070, rev 00, 07/2016), page 28. Open the PDF

#7Room temperature sensor disconnected or cable faulty.

Likely cause: Sensor unplugged or cable damaged.

Truma's checks, in order: Contact Truma service.

Source: Truma VarioHeat (eco / comfort) - operating instructions with CP plus VarioHeat and CP classic VarioHeat (39050-00070, rev 00, 07/2016), page 28. Open the PDF

#11Temperature cut-out has tripped.

Likely cause: Heater overheated.

Truma's checks, in order: Contact Truma service.

Source: Truma VarioHeat (eco / comfort) - operating instructions with CP plus VarioHeat and CP classic VarioHeat (39050-00070, rev 00, 07/2016), page 28. Open the PDF

#25Voltage too high (above 16.4 V).

Likely cause: Faulty charger or other voltage source.

Truma's checks, in order: Check battery voltage and charger.

Source: Truma VarioHeat (eco / comfort) - operating instructions with CP plus VarioHeat and CP classic VarioHeat (39050-00070, rev 00, 07/2016), page 28. Open the PDF

#26Voltage too low (below 10 V).

Likely cause: Flat or worn battery.

Truma's checks, in order: Charge the battery; replace if old.

Source: Truma VarioHeat (eco / comfort) - operating instructions with CP plus VarioHeat and CP classic VarioHeat (39050-00070, rev 00, 07/2016), page 28. Open the PDF

#27Warm-air flow blocked.

Likely cause: Warm-air outlets, return-air intake or duct end outlets closed or blocked.

Truma's checks, in order: Clear blockages and open the end outlets.

Source: Truma VarioHeat (eco / comfort) - operating instructions with CP plus VarioHeat and CP classic VarioHeat (39050-00070, rev 00, 07/2016), page 28. Open the PDF

#28Window above the cowl open (window switch).

Likely cause: Window open or window switch faulty.

Truma's checks, in order: Close the window.

Source: Truma VarioHeat (eco / comfort) - operating instructions with CP plus VarioHeat and CP classic VarioHeat (39050-00070, rev 00, 07/2016), page 28. Open the PDF

#29Battery voltage getting low (below 10.4 V).

Likely cause: Battery discharging.

Truma's checks, in order: Charge the battery.

Source: Truma VarioHeat (eco / comfort) - operating instructions with CP plus VarioHeat and CP classic VarioHeat (39050-00070, rev 00, 07/2016), page 28. Open the PDF

#32Fan motor nearing its wear limit.

Likely cause: Worn heater fan motor.

Truma's checks, in order: Contact Truma service before it fails.

Source: Truma VarioHeat (eco / comfort) - operating instructions with CP plus VarioHeat and CP classic VarioHeat (39050-00070, rev 00, 07/2016), page 28. Open the PDF

#255Heater not talking to the control panel.

Likely cause: Panel cable or main fuse faulty, or cable disconnected.

Truma's checks, in order: Contact Truma service; check panel cable and fuse.

Source: Truma VarioHeat (eco / comfort) - operating instructions with CP plus VarioHeat and CP classic VarioHeat (39050-00070, rev 00, 07/2016), page 28. Open the PDF

Where this comes from

Truma VarioHeat (eco / comfort) - operating instructions with CP plus VarioHeat and CP classic VarioHeat (39050-00070, rev 00, 07/2016), published by Truma. Open the PDF

We don't invent fault codes or part numbers. Each code above carries the page it came from.